Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Parts & Accessories

$170.00 - $179.99
This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation. The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included. - 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center - Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels - Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels - Includes cassette spacer - Material: Aluminum
$119.99 - $139.99
Zipp Speed Weaponry Freehub Bodies - Material: Aluminum
$20.00 - $29.99
These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals. Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.
$109.99
Wheel Freehub Kit—XDR Driver Body Kit—Zipp ZR1 Compatible With: WH-202-FTLD-A1, WH-303-F650-A1, WH-303-FTLD-A1, WH-303-FTLR-A1, WH-303-FTUD-A1, WH-303-FTUR-A1, WH-404-FTLD-A1, WH-404-FTLD-B1, WH-404-FTLR-A1, WH-808-FTLD-A1, WH-808-FTLR-A1, WH-SP9-TLD-A1, WH-SP9-TUD-A2, WH-SP9-TUR-A2
$50.00 - $93.00
Match your Beyond Black hubs, spokes and decals (each sold separately) with skewers from Zipp. - Sold in pairs - Stainless steel: 85 grams/set - Titanium: 78 grams/set
$32.00 - $34.99
Boostinators are hub specific conversions designed to take non-boost hubs and convert them to boost compatibility. Don't toss out that wheelset - Boostinate it.
$54.99
The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA - 7075 T6 Aluminum - Not compatible with RS-1 fork
$14.52
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: JoyTech 9mm x 1, front "parallax" style hub - Compatible with 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Diameter: 15.0mm - Length: 11.0mm - 1 cone per bag COMPATIBLE HUBS: - JoyTech 9mm x 1, front "parallax" style hub - Taiwanese hubs with 9mm x 1 axle
$14.45
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Rear 10mm x 1 axle - Shimano Left Rear Cone - Cone Wrench Size: 15mm - Threads: 10mm x 1 - Cone Diameter: 17.0mm - Dust Seal Diameter: 25.5mm - Length: 16.0mm - 1 cone per bag COMPATIBLE HUBS: - XT M750, 9-spd Rear - XT M760, 9-spd Rear - XT M765, 9-spd Rear - Deore LX M570, 9-spd Rear
$1.80 - $9.99
Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually
$5.00
Rim strips designed for Surly Rabbit Hole 26+. - Rim Strip Width (mm): 38 mm - Adhesive: No - Material: PVC - Wheel Size: 26" - Tire Diameter: 26"
$5.99
Rubber rim strips for 24-inch diameter fatbike rims. - Sold individually
$15.99
• 5mm skewer set (F+R hubs) • Standard 5mm Hex release • Black or Silver anodized finish • Chromoly axles
$2.00
- For square taper and flanged. - Fits most cartridge BBs - Shell: 8mm Flanged axle bolt
$10.99
- Replacement steel quick release skewers
$12.99
• Replacement aluminum quick release skewers
$10.99
• Replacement aluminum quick release skewers
$12.99
- Replacement rear skewer - Spacing: 135mm - Material: Steel
$2.99
- Converts Schrader rims to Presta - Rubber - Sold individually
$12.99 - $22.99
- Supplies full wheel illumination for 700c/29in wheels and smaller - Approximately 40 hrs of battery life - Water resistant design - Includes 3 (AA) batteries - Sold individually (1 wheel) - Easy to install
$30.00
Stan's Cross Country 29er Rim Strip converts standard tubed wheels to tubeless so you can reap the benefits. Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's rim strips create a tight seal with the tire bead, reducing the instances of "burping". Plus, you won't miss dealing with flat tires and you'll save money on tubes!
$30.00
Stan's Cyclocross Rim Strip converts standard tubed wheels to tubeless so you can reap the benefits. Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's rim strips create a tight seal with the tire bead, reducing the instances of "burping". Plus, you won't miss dealing with flat tires and you'll save money on tubes!
$19.99 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
$25.00
Adapts HEX 32 J-Type Front Hubs to 15x100. Compatible with: - HEX J-Type 32H Boost and non-Boost Front Wheels - Also compatible as replacement 15x110 adapters for HEX 32 J-Type Boost Front Hubs. Not compatible with: - HEX 28 Straightpull or HEX Gravel Front Hubs - HEX Straightpull or Gravel Front Wheels. (see HEX 28 front hub adapters) - SPIKE/OOZY/SPOON hubs
$25.59
- Axle adapters for CX/GX/MT-1110 Elite Series rear hubs - Available in standard QR and 12mm thru-axle options - Axles included with adapters - Material: Aly - Color: Blk
$19.99 - $24.99
Converts CenterLock hubs to accept 6-bolt rotors - Available for standard Quick Release as well as Thru-Axle hubs - Extruded alloy collar with CNC shoulder pins and lock ring - Eliminates the need for rotor bolts
$7.99
• Urethane coated nylon • High performance rim strips • 1 pair per box
$5.99 - $39.99
Looking for a super lightweight but badass tubeless sealant? Boom, you've just found it my friend! No Puncture Hassle performs under the most brutal race conditions. The cutting-edge microfiber molecules fill the bigger holes and tears, whilst the advanced latex forms a strong seal instantly. The formula also contains a unique UV detection system that highlights any punctures you haven’t seen during your ride. Developed with the world's top downhillers and pro peloton teams, to give you the finest tire sealant available. It's non-corrosive and easily washes off with water. Compatible with tubeless ready and full UST wheels/tires, No Puncture Hassle works from 15psi-120psi and temperatures from -20°C to +50°C. Our pouch is designed to fit your Presta valve perfectly and is ideal to add to your toolkit or ride pack for emergency top ups on the go! - For Downhill, Enduro and Road tires - Seals tears and holes up to 6mm - Contains UV puncture detection - Won't dry out or ball - Works from 15psi-120psi and temperatures from -20°C to +50°C - Biodegradable
$34.99 - $35.99
Suitable for both mountain and road applications. - Includes 2 x Tubeless Valves, 2 x Narrow Round Bases, 2 x Wider Round Bases, and 2 x Square bases to fit different rim profiles, Spare Alloy Valve cap with integrated valve core remover - Installs securely with a 4mm fitting for a hex wrench of the valve and a 10mm wrench flat on the nut
$31.99
V2 Tubeless valves are stronger, lighter, and even easier to use thanks to the machined aircraft grade 7075 aluminum and Muc-Off's new Tire Insert air ?ow system. The new design features six slots that are machined into the base of the valve stem, allows tubeless sealant ?uid and air to ?ow freely, even when running tubeless tire inserts. - 7075 Machined Aluminum valve stem and cap - Tire Insert air flow system keep air moving freely and compatible with most tire foam inserts - 4mm machined Allen Key slot for easy installation and removal - Includes Valve Core Removal Tool (integrated into spare alloy cap) - Supplied with various rubber bases to optimize fit with multiple rim types
Page 1 of 12 Next page